| Dimensions and weights | |
|---|---|
| Length approx. | 3550 mm |
| Width/depth approx. | 1200 mm |
| Height approx. | 1830 mm |
| Weight approx. | 2800 kg |
Roll over image to zoom in
TREIPINK OPTIturn TX 6222
37,590.00€
Kirjeldus
Tehnilised andmed
Lisad
Kirjeldus
-
- Machine bed made of heavily ribbed cast iron
- One-piece machine base made of steel
- High stiffness of the headstock housing due to heavily ribbed 25GG casting
- All gears of the feed gear made of steel, hardened and ground
- Waves on needle bearings, all components are lubricated in an oil bath
- Hardened and ground spindle ensures tremendous accuracy and durability
- Due to the high cutting performance, a high chip removal during roughing is no problem
- Service-friendly removable rear panel
- Energy chain for gentle line and hose routing
- Lockable chip protection moves with the bed slide with integrated position indicator and coolant hose, manually displaceable
- Decoupled handwheels tested to EN 23125
- Two-channel right-left switch tested to EN 23125
- No change wheels needed
- Switch with life cycle calculation tested according to EN ISO 13849
- With safety device against simultaneous operation of threading and feed mechanism
- Bed guides hardened and precision ground
- Electronically braked engine
- Electronic feed shutdown of the Z axis
- All electronic controls to reach centrally
- Complete illumination of the workspace
- External coolant tank with level indicator and oil separator
- Complete guide and tension spindle cover
- Electrical position switch off with quadruple position stop
- 3-jaw lathe chuck in the standard scope of delivery
- Quick change steel holder SWH 7-C
- 1 steel holder 32 x 130 type D for square chisel 25 mm
- Digital Position Display DP700 (For more information see “NEWALL-DP700”)
- Large spindle bore Ø 105 mm
Tehnilised andmed
| ooling lubricant system | |
|---|---|
| Coolant pump output | 100 W |
| Electrical connections | |
|---|---|
| Total rated value | 8.5 kW |
| Electrical Data | |
|---|---|
| Supply voltage | 400 V |
| Mains frequency | 50 Hz |
| Feed | |
|---|---|
| Longitudinal feed range | 0,05 – 1,5 mm/rev |
| Number of longitudinal feeds | 55 |
| Flat feed range | 0,025 – 0,75 mm/rev |
| Number of flat feeds | 55 |
| Pitches | |
|---|---|
| Metric pitch | 0,5 – 15 mm/rev |
| Number of metric pitches | 55 |
| Imperial pitch | 60 – 2 Gg/1″ |
| Number of imperial pitches | 55 |
| Diametrical pitch | 120 – 4 Gg/π |
| Number of diametrical pitches | 55 |
| Modular thread pitch | 0,25 – 7,5 mm x π |
| Number of modular thread pitches | 55 |
| Speed range | |
|---|---|
| Number of gears | 12 |
| Speed range | 40 – 1650 min¯¹ |
| Spindle | |
|---|---|
| Spindle chuck | Camlock DIN ISO 702-2 No. 8 |
| Spindle bore/rod passage diameter | 105 mm |
| Spindle cone | Ø 113 (cone 1:20) mm |
| Tailstock | |
|---|---|
| Chuck | MT5 |
| Quill stroke | 180 mm |
| Quill diameter | 72 mm |
| Travel | |
|---|---|
| Travel upper slide | 170 mm |
| Travel cross slide | 350 mm |
| Travel carriage saddle | 2000 mm |
| Work areas | |
|---|---|
| Max. height | 310 mm |
| Max. width | 2200 mm |
| Swing diameter above machine bed | 620 mm |
| Swing diameter above planing slide | 424 mm |
| Turning length in bed bridge | 880 mm |
| Bed width | 350 mm |
Lisad
